10Pcs Mini 1A Lithium Battery Charging Module Board With USB Interface
90
Direct purchase from the factory 
Ka sɛn sɔgɔsɔgɔninjɛ
Sɔnni hɔrɔn
Ka taa cogo
Ka segin cogoSɔnni Hɔrɔn
I ni ce Roymall, i ka sɔnniw siti. An bɛ i ka dɛmɛ fɛɛrɛ. O sɔnni hɔrɔn bɛ kɛ i ka sɔnni kɛnɛ kan.Ka Taa Cogo
An bɛ sɔnniw taa i ka so la 2 don kɔnɔ. Kɛnɛ cɛsiri bɛ se ka kɛ 5-7 don kɔnɔ.1. Ka Segin Cogo
Sɔnniw bɛ segin 40 don kɔnɔ. Sɔnni yɛlɛman tɛ segin.2.Ka Sɛn Segin
I bɛ sɛn sɔrɔ segin kɔnɔ.
nt10Pcs Mini 1A Lithium Battery Charging Module Board With USB Interface
nt
ntDescription:
nt
ntCharging method: linear charge 1%
ntCharging current: 1A adjustable
ntCharge accuracy: 1.5%
ntInput voltage: 4.5V-5.5V
ntFull charge voltage: 4.2V
ntCharging indicator: Red charging green full charge
ntCharging input interface: Mini USB
ntWorking temperature: -10°C to +85°C
ntReverse: NO
ntSize: 25 x 19 x 10mm
nt
ntNote:
nt
ntAmpere meter can only be connected to 5V input end of the module.
ntIt is better that the charging current is 37% of the battery capacity. If you charge to the battery of 1000mAH, current of 400 is enough.
ntThe connection wire should not be too long.
ntMake sure the connect point is good.
ntIf the input voltage is too high, like 5.2V, the current will be less than 1000mA, it is normal. It is protection function, Auto-substract the charging current to avoid burn damage to chip.
ntInput reverse has no effect on the chip, but the output (battery terminals) reverse will burn chips.
nt
ntApplications:
nt
ntThis module is used for single-or multi-section parallel lithium lithium rechargeable battery, charging from the USB port to take power.
nt
ntPackage included:
nt
nt10 x 1A lithium battery charging modulen
nt
ntDescription:
nt
ntCharging method: linear charge 1%
ntCharging current: 1A adjustable
ntCharge accuracy: 1.5%
ntInput voltage: 4.5V-5.5V
ntFull charge voltage: 4.2V
ntCharging indicator: Red charging green full charge
ntCharging input interface: Mini USB
ntWorking temperature: -10°C to +85°C
ntReverse: NO
ntSize: 25 x 19 x 10mm
nt
ntNote:
nt
ntAmpere meter can only be connected to 5V input end of the module.
ntIt is better that the charging current is 37% of the battery capacity. If you charge to the battery of 1000mAH, current of 400 is enough.
ntThe connection wire should not be too long.
ntMake sure the connect point is good.
ntIf the input voltage is too high, like 5.2V, the current will be less than 1000mA, it is normal. It is protection function, Auto-substract the charging current to avoid burn damage to chip.
ntInput reverse has no effect on the chip, but the output (battery terminals) reverse will burn chips.
nt
ntApplications:
nt
ntThis module is used for single-or multi-section parallel lithium lithium rechargeable battery, charging from the USB port to take power.
nt
ntPackage included:
nt
nt10 x 1A lithium battery charging modulen
nt
nt
Electronics Ranking
nt
nt
