Geekcreit® DC12V 10A 1CH 433MHz Wireless Relay RF Remote Control Switch Receiver
40
Direct purchase from the factory 
Ka sɛn sɔgɔsɔgɔninjɛ
Sɔnni hɔrɔn
Ka taa cogo
Ka segin cogoSɔnni Hɔrɔn
I ni ce Roymall, i ka sɔnniw siti. An bɛ i ka dɛmɛ fɛɛrɛ. O sɔnni hɔrɔn bɛ kɛ i ka sɔnni kɛnɛ kan.Ka Taa Cogo
An bɛ sɔnniw taa i ka so la 2 don kɔnɔ. Kɛnɛ cɛsiri bɛ se ka kɛ 5-7 don kɔnɔ.1. Ka Segin Cogo
Sɔnniw bɛ segin 40 don kɔnɔ. Sɔnni yɛlɛman tɛ segin.2.Ka Sɛn Segin
I bɛ sɛn sɔrɔ segin kɔnɔ.
>>>Click here to buy the remote control<<<
n
nSpecification:
n
n1. Input Voltage: DC10-14V
n2. Standby Current: <5MA
n3. RF Frequency: 433MHZ
n4. RF Working mode:Super heterodyne receiver
n5. Receiver Sensitivity: >90dBm
n6. Remote Control Distance: >100 meter(In open environment)
n7. Decoding Way: MCU Software decoding
n8. Can store the number of remote control:50
n9. Support remote control type: Fixed code, learning code
n10. Channel: 1CH
n11. Multiple working modes: (Jog/Non-Latched ,inter-lock/Latched ,self-lock /Self-Latched,Delay off)
n12. Wiring Method:Fixed wiring terminal
n13. Working Voltage: DC12V
n14. Output Current: 10A
n15. Rated load:10A 250VAC / 10A 125VAC, 10A 30VDC / 10A 28VDC
n16. Output:Normally open,Common,Normally closed
n17. Dimension:3.5cm*3cm*1.6cm
n
nWorking/output way:
n
n1.Jog: Press the learning button then release, set the mode from the system automatically working mode to action mode, wait for a while, when the board LED off, said it is into the learning state, press the remote control, the system received the signal. The LED flashes 5 times and goes off again. After 3S delay, LED light marked learning success, the system automatically withdraw from the learning state.
n2.Self-locking: Press the learning button, then release, press 2 times, the system automatically set to self-locking mode, wait for a while, LED off, it is into the learning state, press the remote control, LED flash 5 times Off. 3S after the delay, LED light learning success.
n3.Interlock: press the learning button, then release, press 3 times in succession, the system is set to interlock mode.
n4.Delay: Press remote control relay pull-in,release the remote control and begin timekeeping,after 5s,10s,15s will automatically close the relay
n
nDescription:
n
n1. Press the learning code .the indicator flash ,loosen your finger ,press any button of the remote control
nthe indicator flash 2 times and off .it mean you learn it successfully .
n2. It can learn more than 12 PCS 2262 or 1527 chip with the different code wireless 433MHz remote control
n3. Remove/clean :press the learning button about 8 seconds , the indicator turn on to off, it means the information that you keep have been removed successfully .
n
nPackage included:
n
n1/2/3/5/10/20 x 12V 1CH 433MHz Wireless Relay Switch Receiver (optional)
n
nSpecification:
n
n1. Input Voltage: DC10-14V
n2. Standby Current: <5MA
n3. RF Frequency: 433MHZ
n4. RF Working mode:Super heterodyne receiver
n5. Receiver Sensitivity: >90dBm
n6. Remote Control Distance: >100 meter(In open environment)
n7. Decoding Way: MCU Software decoding
n8. Can store the number of remote control:50
n9. Support remote control type: Fixed code, learning code
n10. Channel: 1CH
n11. Multiple working modes: (Jog/Non-Latched ,inter-lock/Latched ,self-lock /Self-Latched,Delay off)
n12. Wiring Method:Fixed wiring terminal
n13. Working Voltage: DC12V
n14. Output Current: 10A
n15. Rated load:10A 250VAC / 10A 125VAC, 10A 30VDC / 10A 28VDC
n16. Output:Normally open,Common,Normally closed
n17. Dimension:3.5cm*3cm*1.6cm
n
nWorking/output way:
n
n1.Jog: Press the learning button then release, set the mode from the system automatically working mode to action mode, wait for a while, when the board LED off, said it is into the learning state, press the remote control, the system received the signal. The LED flashes 5 times and goes off again. After 3S delay, LED light marked learning success, the system automatically withdraw from the learning state.
n2.Self-locking: Press the learning button, then release, press 2 times, the system automatically set to self-locking mode, wait for a while, LED off, it is into the learning state, press the remote control, LED flash 5 times Off. 3S after the delay, LED light learning success.
n3.Interlock: press the learning button, then release, press 3 times in succession, the system is set to interlock mode.
n4.Delay: Press remote control relay pull-in,release the remote control and begin timekeeping,after 5s,10s,15s will automatically close the relay
n
nDescription:
n
n1. Press the learning code .the indicator flash ,loosen your finger ,press any button of the remote control
nthe indicator flash 2 times and off .it mean you learn it successfully .
n2. It can learn more than 12 PCS 2262 or 1527 chip with the different code wireless 433MHz remote control
n3. Remove/clean :press the learning button about 8 seconds , the indicator turn on to off, it means the information that you keep have been removed successfully .
n
nPackage included:
n
n1/2/3/5/10/20 x 12V 1CH 433MHz Wireless Relay Switch Receiver (optional)
Electronics Ranking
